"*" indicates required fields

ROGUEWORX Genesis VSR Hop Conversion

$200$215

All Information is pulled from Rogueworx website here: https://www.rogueworx.com/

GENESIS HOPUP INFO:

This is an 11-piece kit that provides you with all the parts required to make your KJW KC-02 compatible with the wide variety of VSR/GBB hop rubbers and VSR barrels out there in the airsoft world (because the standard KC-02 barrel, rubber and hop unit are proprietary to the KC-02), but also does soooo much more! Over a year of development and testing went into this kit, as well as an extensive beta-testing programme with airsoft tech experts around the world.

You can watch the walk-through and installation video here: https://youtu.be/ygNopQaoDgY

The diagram in the pictures explains much of the detail of each part, here’s a high-res download link for it: https://www.dropbox.com/s/zp9uob1gqx8fll6/Genesis%20promo%20A3%20b.png?dl=0

The kit contains 11 parts:

KC-VSR™ Cylinder-Nozzle V6, 7075 CNC aluminium, GOLD anodised
Genesis™ Hop Unit V4A, 6061 CNC aluminium, RED anodised
Diadem™ Hop Wheel V3A, 7075 anodised CNC aluminium
3 x Hop Keys: Arch (gold), Bridge (blue), Flat (purple). 6061 anodised CNC aluminium
3 x Flow Restrictors: Low (green), Medium (blue), High (red). 6061 anodised CNC aluminium. (Maximum power is achieved by not using a flow restrictor at all)
1 x 3mm neodymium magnet, for use with standard KJW hop wheel
1 x 2.5mm steel cylinder cross-pin
This kit solves problems with poor air seal, solves the problem of broken cylinders, allows greater control of hop pressure and adjustment resolution, allows use of a huge range of existing VSR hop rubbers and barrels, and many other small improvements in functionality. It is a quantum leap forward in the performance and upgradeability of the KC-02 platform that has never been done successfully before.

Testing has shown that 60 degree hardness hop rubbers are best suited for this hop unit due to the amount of pressure it applies when using heavy ammo such as 0.36g – 0.45g weights.

The latest improvements to the Genesis kit should reduce the amount of bedding-in time required after installing the new parts, but some manual dry-racking may still be required for a few minutes. We recommend plenty of lubrication then cleaning inside the gun once it cycles smoothly.

The most common area to cause problems is the top of your trigger mech above the valve striker where the cylinder slides across the top of the trigger mech between the “turrets”. This area usually has some rough casting in the corners which needs to wear down to suit the new cylinder. This isn’t a problem for everybody but some of our beta testers used a file to smooth this area first. We found that racking the gun a couple dozen times and cleaning, followed by just shooting the gun for a while was more than sufficient to cut this area to the new parts.

Barrel and Hop Rubber Combo’s we’ve tested and confirmed they fit, though performance varies:

50deg Flamingo rubber + ML Crazy Jet barrel
60deg Flamingo rubber + ML Crazy Jet barrel
60deg Flamingo rubber + TNT barrel (bridge removed)
60deg Airsoft Philosopher rubber and barrel
60deg G&P VSR rubber + Prometheus VSR barrel
60deg TM VSR rubber + R-hop Prometheus VSR barrel
70deg ML Autobot rubber + ML Crazy Jet barrel
60deg ML Autobot rubber + ML Crazy Jet Barrel
60deg PDI rubber + R-hopped PDI barrel
Laylax purple rubber + Laylax 6.03 barrel
60deg ML Monster rubber + Laylax barrel
60deg ML Delta rubber + Laylax barrel
EDGI barrels in “TM Pistol” cut (unbridged)
PLEASE NOTE: Do not install the metal C-clip on the hop rubber that comes with Maple Leaf hop rubbers. It is not necessary and will cause cycling problems as the grip on the nozzle will be too tight.

SKU: rogueworx-genesis Category: